Power it ALL!! The Q1212 has Enough Horsepower to Challenge the Legendary P3000!
Connect this Bad Boy to any of Electro Voice’s Phoenix, Tour X, and ZX3/ZX5 systems or system combinations and deliver Ear Bleeding Audio to the Masses! The Q Series utilizes an efficient Class-H amplifier design where the permanent voltage rail is designed to cover the average music signal, rather than continuing to supply the voltage for max output. When dynamic peaks need a higher output voltage the voltage rail switches over to maximum saving up to 50% of the power consumption and reducing heat output.
Q Series combines the sonic excellence and ruggedness of its Precision Series predecessors with Class-H innovation, all in a compact and affordable package.
Electro Voice Q1212 Features
Clearly One of the Most Powerful Amp Designs in a 2U Chassis
2x1200 Watts @ 4 Ohms (2x1800 Watts @ 2 Ohms)
Class-H, Power Saving design
Dynamic Headroom and Transient Response
Protection Package and Dynamic Limiter
Parallel loop thru XLR output to add additional power amps
Speakon A/B Outputs
Audio Performance
While many people understand there are tremendous differences between professional loudspeakers, many also tend to think that amplifiers are only differentiated by the amount of output power they provide. Electro-Voice amplifiers serve to prove that there are also audible differences...
Q-Series Amplifiers and Connectivity
Whatever application you choose, you can be sure your Q Series amp is prepared:
Both inputs have a paralleled loop thru XLR output to route signal to other amp inputs
Besides the usual channel A/B outputs via Speakon connectors (on pin 1+/1-), output A carries the signal of channel B as well (on pin 2+ / 2-), providing an easy drive option for biamped speakers
Parallel & Bridge Mode option switches provide additional functionality with minimized cabling requirements
An additional switchable LPN (Low-Pass Notch) filter provides extra tonal fundament and kick, with protective Low-
Cut for using smaller passive 12 or 15 inch cabinets without additional subwoofers
Unclipped Signal Clipped Signal Dynamic Limiter Signal
Dynamic Headroom
Amplifier power and distortion figures are typically specified with sine wave signals. However, music signals are far more dynamic than sine waves, comprising a pulsed wideband spectrum.
EV believes that, above all figures, the tonal performance of live music counts most; therefore, all of their amplifiers are designed for dynamic headroom. This means that each and every EV amp has at least 30% more output capability for short-term signals, when compared to a long-term sine wave value. This additional headroom results in an amp that will, for example, allow for short term signal peaks of at least 780W when spec´d at 600W.
While dynamic headroom is audible when playing music through a sound system, another specification to observe is the increase in output power from an 8 Ohm load to 4 Ohms, and then down to 2 Ohms. Of course, all Electro-Voice amplifiers are designed to be absolutely stable into loads of 2 Ohms.
Transient Response
When processing dynamic signals, other important criteria are signal speed and dynamic distortion. For example, kick drum signals carry pulses of many frequencies as an overlay spectrum. Therefore, and in contrast to many other manufacturers, EV specifies a lot more information on their amplifiers’ dynamic behavior than just
slew rate figures. Important tests referring to the amp´s ability regarding multitone signal pulses are expressed by IMD-SMPTE measurements at high power levels. And, while IMD tests show the Intermodulation Distortion behavior (how much
sound is added by the amplifier), DIM30 is the real spec for speed in an amplifier. All these tests are carried out in EV labs during an amplifier’s design phase, to ensure maximum sonic performance. While these technical explanations appear very complex, they are clearly audible. Take a Q-Series amplifier and crank it up, you’ll hear the difference immediately!
Protection Package and Dynamic Limiter
There are many good-sounding amplifiers available; however, for an amp to be considered the world’s best requires unparalleled reliability in real-world applications.
Q Series amplifiers benefit from decades of professional amplifier design, and all the expertise that has made EV amps the concert/touring standard is built into Q Series. Our complete protection package includes sophisticated circuits against overheating, short circuit, DC output voltage, HF oscillation, back EMF (Electromotive Force), and destructive peak current.
Furthermore, Q Series amps also protect your valuable loudspeakers with built-in dynamic limiters, preventing dangerous output clipping. The limiters immediately reduce amp gain when dynamic headroom is pushed to the limits at maximum output, keeping distortion below 1% in a situation that can otherwise cause a signal to clip, which is often fatal for woofers and drivers.
Specifications and additional product information for: Electro Voice Q1212 Power Amplifier Specifications
Maximum Midband Output Power: THD = 1%, 1 kHz, Dual Channel
1800 Watts @ 2 Ohms
1200 Watts @ 4 Ohms
750 Watts @ 8 Ohms
Rated Output Power: THD < 0.1%, 20 Hz-20 kHz
1100 Watts @ 4 Ohms
550 Watts @ 8 Ohms
Maximum Single Channel Output Power: Dynamic-Headroom, IHF-A
3400 Watts @ 2 Ohms
1800 Watts @ 4 Ohms
950 Watts @ 8 Ohms
Maximum Single Channel Output Power: Continuous, 1 kHz
2400 Watts @ 2 Ohms
1500 Watts @ 4 Ohms
850 Watts @ 8 Ohms
Maximum Bridged Output Power: THD = 1%, 1 kHz
3600 Watts @ 4 Ohms
2400 Watts @ 8 Ohms
Maximum RMS Voltage Swing: THD = 1%, 1 kHz
Power Bandwidth: THD = 1%, ref. 1 kHz, half power @ 4 Ohms
Voltage Gain: ref. 1 kHz
Input Sensitivity: rated power @ 8 Ohms, 1 kHz
THD: at rated output power MBW = 80 kHz, 1 kHz
IMD-SMPTE 60 Hz, 7 kHz: < 0.1%DIM30, 3.15 kHz, 15 kHz: < 0.05%Maximum Input Level: +21 dBu (8.69 Vrms)Crosstalk: ref. 1 kHz, at rated output power
Frequency Response: ref. 1 kHz
Input Impedance: active balanced
Damping Factor, 1 kHz: > 303Slew Rate: 30 V/µsSignal to Noise Ratio: Amplifier, A-weighted
Output Noise: A-weighted
Output Stage Topology: Class HPower Consumption: 1/8 maximum output power @ 4 Ohms
Power Requirements: (factory configured)
244 V or 230 V
120 V or 100 V
50 Hz-60 Hz
Protection:
Audio limiters
High temperature
DC, HF, Back-EMF
Peak current limiters
Inrush current limiters
Turn-on delay
Cooling: Front-to-rear, 3-stage-fansAmbient Temperature Limits: 5-40 °C (40-105 °F)Signal Processing: LPN, switchableSafety Class: IDimensions (WxHxD): 19 x 3.5 x 16.6 inches (483 x 88.1 x 421.5 mm)Weight: 39 lbs (17.7 kg)
norm.jpg)
