1 of 3

B&C 21SW152-4 21" Neodymium Subwoofer 4 Ohm

B&C's 21SW152 features a massive 260 square inches of diaphragm surface area, nearly 40% more than an 18" driver and equal to double the Sd of a typical 15". A 6" diameter voice coil with a 1" copper winding length provides great Xmax (15 mm) and impressive power handling (2,000 watts RMS). Despite the driver's size, a high-strength neodymium ring magnet keeps overall weight as low as possible. The 21SW152 will deliver nearly unmatchable low frequency output when loaded into vented or horn loaded enclosures. Perfect for high output concert and nightclub applications. Specifications: *Power handling: 2,000 watts RMS, 4,000 watts continuous program *VCdia: 6" *Le: 1.4 mH *Impedance: 4 ohms *Re: 3.3 ohms *Frequency response: 30-1,000 Hz *Fs: 35 Hz *SPL: 97 dB 1W/1m *Vas: 6.15 cu. ft. *Qms: 7.3 *Qes: 0.33 *Qts: 0.32 *Xmax: 15 mm *Dimensions: A: 21.5" B: 20" C: 10.3"

4,000 watt continuous program power capacity
6" diameter, 1" long split winding copper voice coil wound on fiberglass former
15 mm Xmax, 60 mm peak-to-peak excursion before damage
Neodymium ring magnet allows a very high force factor and linear excursion
Ventilated voice coil gap for reduced power compression
Aluminum demodulating ring decreases distortion
Double silicone spider with optimized compliance
Triple roll surround
Water-resistant cone coating

B&C Speakers

B&C cone loudspeaker models range from 6.5" to 21", each built on a sturdy die-cast aluminum chassis for maximum mechanical reliability. Voice coils are wound in two layers inside-outside around polyimide or fiberglass formers, giving them the ability to withstand very high thermal stress. Loudspeaker cones are treated with a special stiffening finish, resulting in excellent rigidity and avoiding break-up problems when driven to full power.

Many B&C speakers include carefully balanced copper or aluminum rings that minimize variations in the magnetic field during operation, reducing distortion and increasing accuracy in reproduced sound. Most models also feature a specially designed cooling path through the magnet assembly to further increase power handling and lower power compression. The NDL, NW, HPL, and NCX models use powerful neodymium magnets which offer a weight reduction of up to 60%, and special chassis designs for improved cooling.

The design and optimization are performed with up-to-date Finite Element Analysis (FEA) to obtain the best combination of efficiency, linearity, and thermal exchange. Ongoing research and refining of the theoretical models and a constant updating of the measurement methods and instruments allow B&C to further increase excursion capabilities, consistency, and overall sound quality.

Price$907.00

Bogen C-100 100W Amplifier

The Classic Series of P.A. amplifiers are the result of Bogen's commitment to provide products that meet the need of the commercial sound industry. Each amplifier accommodates up to four inputs: 2 balanced microphone inputs, 1 high impedance auxiliary input, and 1 input from a telephone line, or 1 microphone, 2 auxiliary, and 1 telephone input. A front panel selector switch is used to select either the MIC2 or AUX1 input. Each channel is equipped with its own volume control. Treble and bass controls are provided to adjust tonal balance. Output screw terminals are provided for 8 and 16 ohm balanced and 4 ohm unbalanced systems, and for 25 volt and 70 volt constant voltage systems. Also features a microphone precedence circuit and thermal/electrical protection against abnormal heat build up, short circuits, and overload. UL and CSA listed. Frequency response: 20-20,000 Hz (+/-1 dB). Distortion: <1% 70-16,000 Hz at full rated power. Dimensions: 12-1/2" W x 3-3/4" H x 11" D.

List Price: $599.99

Price$529.98

Bogen C-60 60W Amplifier

The Classic Series of P.A. amplifiers are the result of Bogen's commitment to provide products that meet the need of the commercial sound industry. Each amplifier accommodates up to four inputs: 2 balanced microphone inputs, 1 high impedance auxiliary input, and 1 input from a telephone line, or 1 microphone, 2 auxiliary, and 1 telephone input. A front panel selector switch is used to select either the MIC2 or AUX1 input. Each channel is equipped with its own volume control. Treble and bass controls are provided to adjust tonal balance. Output screw terminals are provided for 8 and 16 ohm balanced and 4 ohm unbalanced systems, and for 25 volt and 70 volt constant voltage systems. Also features a microphone precedence circuit and thermal/electrical protection against abnormal heat build up, short circuits, and overload. UL and CSA listed. Frequency response: 20-20,000 Hz (+/-1 dB). Distortion: <1% 70-16,000 Hz at full rated power. Dimensions: 12-1/2" W x 3-3/4" H x 11" D.

List Price: $499.99

Price$355.00

Bogen GS-100 100W Amplifier with Dual EQ

The Gold Series was designed with the sound contractor in mind. Each amplifier has 6 microphone inputs, 2 auxiliary inputs, and 1 telephone paging input. XLR inputs are provided for Mics 1-4, RCA jacks are provided for AUX input, screw terminals for Mics 5 & 6 and telephone input. Output taps include: 8 ohm, 25 volt, 25 volt center tap, 70 volt, and 100 volt, as well as direct 4 ohm, tape out, preamp out, power amp in, and booster out. Other features include: * Dual Equalizer for acoustic shaping or feedback control * Aphex Aural Exciter circuit for added presence and intelligibility * Phantom power * Contour control * Precedence circuitry * Remote volume control * Auto mute on telephone page * Low cut filter * Frequency response: 20-20,000 Hz +0/-1dB (direct), 65-20,000 Hz +0/-2 dB (transformer) * Distortion: 0.5% (max), 0.3% (typical) * Dimensions: 3-1/2" H x 16-1/2" W x 12" D.

List Price: $799.99

Price$495.00

Bogen GS-150 150W Amplifier with Dual EQ

The Gold Series was designed with the sound contractor in mind. Each amplifier has 6 microphone inputs, 2 auxiliary inputs, and 1 telephone paging input. XLR inputs are provided for Mics 1-4, RCA jacks are provided for AUX input, screw terminals for Mics 5 & 6 and telephone input. Output taps include: 8 ohm, 25 volt, 25 volt center tap, 70 volt, and 100 volt, as well as direct 4 ohm, tape out, preamp out, power amp in, and booster out. Other features include: * Dual Equalizer for acoustic shaping or feedback control * Aphex Aural Exciter circuit for added presence and intelligibility * Phantom power * Contour control * Precedence circuitry * Remote volume control * Auto mute on telephone page * Low cut filter * Frequency response: 20-20,000 Hz +0/-1dB (direct), 65-20,000 Hz +0/-2 dB (transformer) * Distortion: 0.5% (max), 0.3% (typical) * Dimensions: 3-1/2" H x 16-1/2" W x 12" D.

List Price: $999.99

Price$575.00

Bogen GS-35 35W Amplifier with Dual EQ

The Gold Series was designed with the sound contractor in mind. Each amplifier has 6 microphone inputs, 2 auxiliary inputs, and 1 telephone paging input. XLR inputs are provided for Mics 1-4, RCA jacks are provided for AUX input, screw terminals for Mics 5 & 6 and telephone input. Output taps include: 8 ohm, 25 volt, 25 volt center tap, 70 volt, and 100 volt, as well as direct 4 ohm, tape out, preamp out, power amp in, and booster out. Other features include: * Dual Equalizer for acoustic shaping or feedback control * Aphex Aural Exciter circuit for added presence and intelligibility * Phantom power * Contour control * Precedence circuitry * Remote volume control * Auto mute on telephone page * Low cut filter * Frequency response: 20-20,000 Hz +0/-1dB (direct), 65-20,000 Hz +0/-2 dB (transformer) * Distortion: 0.5% (max), 0.3% (typical) * Dimensions: 3-1/2" H x 16-1/2" W x 12" D.

List Price: $499.99

Price$360.00

Subcategories