The ElectroVoice EVID 12.1 is a passive, surface-mount installation subwoofer featuring a 12" driver, dual voice coils that process both channels of stereo low end information, a 175-Watt per coil power reservoir, and a 160Hz passive crossover. In addition, the EVID 12.1 can distribute audio for up to four separate satellites, via the four crossed-over audio outputs on the back panel, and may be wall or ceiling mounted with the supplied custom hardware. This provides extended bass performance for installation applications in bars, restaurants, and meeting or event facilities, as a companion to the Electrovoice EVID series of loudspeakers. • Unique 12" dual voice coil design accepts Left/Right stereo low end program material • 175-Watt power handling per voice coil • Built-in passive stereo crossover • Side/Front angled port system for improved low frequency dispersion • Wall or ceiling mounted MDF enclosure • High SPL and Sensitivity • Forged steel eyebolt for attaching safety line if hanging the enclosure • Four-satellite speaker output connection available as dual pairs or separate daisy-chained single units

Power it ALL!! The Q1212 has Enough Horsepower to Challenge the Legendary P3000!
Connect this Bad Boy to any of Electro Voice’s Phoenix, Tour X, and ZX3/ZX5 systems or system combinations and deliver Ear Bleeding Audio to the Masses! The Q Series utilizes an efficient Class-H amplifier design where the permanent voltage rail is designed to cover the average music signal, rather than continuing to supply the voltage for max output. When dynamic peaks need a higher output voltage the voltage rail switches over to maximum saving up to 50% of the power consumption and reducing heat output.

The Electro-Voice Q66 II power amplifier is a versatile workhorse with 2 x 600W @ 4 ohms and 2 x 900W @ 2 ohms. It has plenty of power to drive a huge variety of speaker systems, including Sx300, ZX4, Sb122, and more.Dynamic Headroom:Electro-Voice's philosophy is that tonal performance of live music counts most; therefore, Electro-Voice amps are designed for dynamic headroom, meaning that each and every Electro-Voice amp—including the Q66 II—has at least 30% more output capability for short-term signals when compared to a long-term sine wave value. This additional headroom results in an amp that will, for example, allow for short term signal peaks of at least 780W when spec'd 600W. While dynamic headroom is audible when playing music through a sound system, another specification to observe is the increase in output power from an 8-ohm load to 4 ohms, and then down to 2 ohms. Of course, all Electro-Voice power amplifiers are designed to be absolutely stable into loads of 2 ohms.

Electro Voice Q99 Power Amplifier

Club Sized Power! The Q99 is a Serious Power Amp Designed to Drive the Tops and Subs for Venue-Sized Systems!
Hook it up to Add Electro Voice’s Tour X or QRx subs and speakers and just listen to it pound out the sound! The Q Series utilizes an efficient Class-H amplifier design where the permanent voltage rail is designed to cover the average music signal, rather than continuing to supply the voltage for max output. When dynamic peaks need a higher output voltage the voltage rail switches over to maximum saving up to 50% of the power consumption and reducing heat output.

Q Series combines the sonic excellence and ruggedness of its Precision Series predecessors with Class-H innovation, all in a compact and affordable package.

A 30-watt "explosion-proof" driver that will not create a spark or detonate in an explosive atmosphere. Integral sintered bronze acoustic screen and heavy die-cast aluminum case meet the UL standards for explosion-proof classification. Meets or exceeds standards for use in hazardous areas classified as Class I - Groups B, C and D. Dual 1-inch screw-on exits, 8-ohm impedance. Driver housing is designed to contain a University Sound 5030 transformer for 20/70.7-volt distributed systems. Transformer purchased separately.

Model 848AT is a wide-range, integrated horn and driver system with a single driver unit having two coaxial horns coupled to opposite sides of the driver diaphragm.

The folded construction of the rear horn coupled with the smaller dimensions of the front horn, present a 1,000 Hz acoustic crossover. This separation of frequencies provides a more extended high frequency response and cleaner sound.

The 150° horizontal by 110° vertical dispersion pattern is beneficial in many applications requiring a wide coverage pattern. Furthermore, excellent loading is maintained to a low-frequency cutoff of 200 Hz.

Model 850T is a wide-range, integrated horn and driver system with a single driver unit having two coaxial horns coupled to opposite sides of the driver diaphragm.

The folded construction of the rear horn coupled with the smaller dimensions of the front horn, present a 1,000 Hz acoustic crossover. This separation of frequencies provides a more extended high-frequency response and cleaner sound.

The 150° horizontal by 110° vertical dispersion pattern is beneficial in many applications requiring a wide coverage pattern. Furthermore, excellent loading is maintained to a low-frequency cutoff of 180 Hz.

Compact Precision Series Class-H Power Amplifier

Electro-Voices new Precision Series Compact amplifiers offer proven Precision Series performance and reliability in a new compact, lightweight format made possible by a highly efficient Class-H design, which generates considerably less heat. The CP3000S is not only the first Precision Series amplifier to use a switch-mode power supply, but also the first switch-mode amplifier with EVs Precision Series sound. With up to 2x1600 watts into two ohms, and 2x1100 watts into four ohms, and only 17.96 lbs (8.15 kg it is both powerful and lightweight.

The Electro-Voice CP4000S is a 2-channel, 2U rack-mount power amplifier designed for the rigors of live touring, offering high efficiency and great quality sound. Three user-selectable performance modes are available - dual, parallel, and bridged. The amplifier features XLR input connectors and XLR and Speakon output connectors for connection to any professional sound system.

The CP4000S uses an optimized power supply with low-leakage toroidal transformers for outstanding audio performance with extensive headroom. Internal circuitry minimizes potential damage from electrical and thermal overload, short circuits, and HF/DC at the outputs. Other protection measures include back-EMF-protection, which prevents damage to the output resistors by electrical back-feed, an inrush current limiter, delayed connection of the outputs at power-up, and dual three-speed fans.

The CPS 8.5 is a four-channel amplifier from Electro-Voice featuring groundbreaking Class-D technology for maximum amp efficiency and minimized heat dissipation in 19" racks.

Each channel individually provides transformer-less, switchable output characteristics, which enable specific channels to achieve maximum performance. Power into 2 Ohms, 4 Ohms, 70V or 100V lines are all possible, and no transformer is required. In Hi-Z operation (70V or 100V), a 50 Hz high-pass filter provides protection against loudspeaker transformer saturation. Additionally, amplifier channels can be bridged in pairs for double output power.

The contractor-friendly CPS 8.5 also features Phoenix-type connectors for inputs and outputs, pre-programmable power-on delay, easy power switching via remote contact closure, and rear level controls.

A module slot for the optional RCM-810 remote control module provides control network functionality, allowing for remote system diagnostics via IRIS-Net software. In addition, using the RCM-810’s Variable Load Drive (VLD) feature can tailor the amplifier’s output power to match every load from 2 Ohms up to 10 Ohms in steps of 0.1 Ohms.

The DL10X low/mid-frequency speaker is a 10", 8-ohm driver designed for professional high-level monitoring and sound reinforcement. Incorporated into the design are 3 exclusive Electro-Voice innovations: PROTEF, a Teflon-based coating, the Thermal Inductive Ring, and
the Flux Demodulation Device.

Also included in the DL10X speaker design are aluminum castings fastened to the pole of the magnet to control inductance and provide
a major heat transfer from the voice coil, which improves power handling and reduces thermal dynamic-range compression.

Electro Voice DL12ST Description:

The Electro-Voice DL12ST is a 12", 300-watt component woofer for P.A. cabinets, featuring extended-length voice-coils for accurate, dynamic low-frequency program content. The speaker is equipped with a proprietary heat-transfer system for long-term performance reliability.

A patented DL12BFH Flux Demodulation Device encircles the unit's voice-coil and the pole piece, providing an additional heat transfer path, and thereby reducing distortion across the band. The voice coils are electrically insulated from adjacent metal parts, further reducing damage from rubbing friction during extreme power peaks.

The ideal 15 in. for high-power bass boxes or 2-way systems. EV's RMD technology provides smooth vocal performance with low-frequency impact. Specs include a high power rating of 350 watts, 45 - 2,000 Hz frequency response, 8 ohms, 12 lbs.

Woofers
EV component woofers are high-efficiency designs highly refined from years of development and field experience. They employ extended-length voice coils for high-impact reproduction of dynamic low-frequency program. All woofers feature proprietary heat-transfer systems for unmatched power capacity and reliability. Kevlar(R)-fiber-composite cones are used to provide structural strength to resist collapse during explosive dynamic peaks and to provide internal mechanical damping to minimize resonances that can change the character of the sound at high levels. The DL15BFH woofer is made of a cast aluminium frame with push terminals, and features Ring-Mode Decoupling (RMD).

Electro Voice Speakers EV DL15STSpeakers are high-efficiency designs highly refined from years of development and field experience. They employ extended-length voice coils for high-impact reproduction of dynamic low-frequency program. All Electro Voice Speakers EV Speakers feature proprietary heat-transfer systems for unmatched power capacity and reliability. Kevlar-fiber composite cones are used to provide structural strength to resist collapse during explosive dynamic peaks and to provide internal mechanical dampening to minimize resonance’s that can change the character of the sound at high levels. DL and EVX woofers are made of cast aluminum frames with push terminals and all features Ring-Mode Decoupling (RMD) except for the DL18MT and the EVX180B.

The Electro-Voice DL18MT subwoofer speaker is an 18-inch, 8-ohm driver designed for professional high-level, high fidelity monitoring and sound reinforcement.

Incorporated into the design of this low frequency speaker are three exclusive Electro-Voice innovations; PROTEF coating, a Teflon-based coating, the Thermal Inductive Ring, and the Flux Demodulation Device.

Also included in the Electro-Voice subwoofer are aluminum castings fastened to the pole of the magnet to control inductance and provide a major heat transfer from the voice coil, which improves power handling and reduces thermal dynamic-range compression.

Part of Electro-Voice's Live X series of portable powered and passive loudspeakers, the ELX112 can be used with a wide range of amplifiers or powered mixers due to its exceptionally efficient design and power handling capability. Designed with the latest Electro-Voice-engineered woofer and 1.5" titanium compression driver, the ELX112 12" passive loudspeaker provides exceptional audio quality with 250W power handling (1000W peak), exceptional SPL output, and a 82Hz-18kHz frequency response. The ELX112 is constructed of 9-ply, 15mm plywood, and is internally braced, making it sturdy yet completely portable. It has built-in side handles for transport, and pole mount for stacking it on top of a acoustically matched Live X series sub.

High performance torroidal power and output transformers combine clean saturation free audio performance with cool running operation. The PA1250T features many of the same comprehensive protection circuits typical in EV amplifiers. Complete protection is provided for high temperature, audio limiters, power up delay and peak current limiters. In addition to the rated output power, the PA1250T provides excellent headroom for a wide dynamic range on music signals. The onboard dynamic limiter ensures that the output clipping of the PA1250T will not will not generate excessive distortion. A detented and marked level control on the rear panel provides hidden reliable level adjustments for the channel. Front panel LED indicates signal present, 0 dB, and limit. Phoenix type connectors for inputs and outputs provide easy rack wiring.